MSI P965 NeoベースのマシンにLinuxをインストールする
実験のためTsukumoからeX.computer Aero Stream B30J-6360E2を買いました．最新機種なのですが，最近Linuxの進展も著しくて大丈夫だと思いました．実際にインストールしてみると，案外にトラブルが発生してしまい，いろいろネットで調べてなんとか（意外に簡単？）できましたのでここでメモしておきます．
問題がマザーボード MSI P965 Neo に関わっています．実は，Ubuntu Linux（6.06も6.10 betaも）は起動しません．RIP LinuxやCent OS 4.4は起動しますが，CDドライブが見つかりませんでした．これは，JMicron製のIDEチップJMB361のドライバーが原因なのです．起動時に all-generic-ide というカーネルオプションを付けると大丈夫のはずです（が，Ubuntuだけはやはりだめでした．See also http://www.ubuntuforums.org/showthread.php?t=233540）．
結局 Cent OS 4.4をインストールしました（/boot/grub/menu.lstにあるカーネルオプションに all-generic-ideをつけないで起動する kernel panic が出るぞ）．しかしネットカードは認識されません．なんでやろう？？？．（続く）
参考のためdmesgメッセージを載せます．御覧の通り，APIC errorがたくさん出ています．
Bootdata ok (command line is ro root=LABEL=/ all-generic-ide)
Linux version 2.6.9-42.ELsmp (buildcentos@mehak.karan.org) (gcc version 3.4.6 20060404 (Red Hat 3.4.6-3)) #1 SMP Tue Aug 15 10:35:26 BST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fedf800 (usable)
BIOS-e820: 000000003fedf800 - 000000003fee0000 (reserved)
BIOS-e820: 000000003fee0000 - 000000003fee3000 (ACPI NVS)
BIOS-e820: 000000003fee3000 - 000000003fef0000 (ACPI data)
BIOS-e820: 000000003fef0000 - 000000003ff00000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
ACPI: RSDP (v000 IntelR ) @ 0x00000000000f91a0
ACPI: RSDT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fee3040
ACPI: FADT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fee30c0
ACPI: MCFG (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fee7a40
ACPI: MADT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fee7940
ACPI: SSDT (v001 PmRef Cpu0Ist 0x00003000 INTL 0x20041203) @ 0x000000003fee7ac0
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20040311) @ 0x000000003fee7f50
ACPI: DSDT (v001 INTELR AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
No NUMA configuration found
Faking a node at 0000000000000000-000000003fedf000
Bootmem setup node 0 0000000000000000-000000003fedf000
No mptable found.
On node 0 totalpages: 261855
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 257759 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
Setting APIC routing to flat
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3ff00000:a0100000)
Checking aperture...
Built 1 zonelists
Kernel command line: ro root=LABEL=/ all-generic-ide console=tty0
IDE generic will claim all unknown PCI IDE storage controllers.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2395.993 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 1025096k/1047420k available (2105k kernel code, 0k reserved, 1297k data, 196k init)
Calibrating delay using timer specific routine.. 4796.27 BogoMIPS (lpj=2398137)
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security failed.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
using mwait in idle threads.
CPU0: Physical Processor ID: 0
CPU0: Processor Core ID: 0
CPU0: Initial APIC ID: 0
Using IO APIC NMI watchdog
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU0: Physical Processor ID: 0
CPU0: Processor Core ID: 0
CPU0: Initial APIC ID: 0
CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
per-CPU timeslice cutoff: 509.62 usecs.
task migration cache decay timeout: 1 msecs.
Booting processor 1/1 rip 6000 rsp 10037e95f58
Initializing CPU#1
Calibrating delay using timer specific routine.. 4791.14 BogoMIPS (lpj=2395572)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU1: Physical Processor ID: 0
CPU1: Processor Core ID: 1
CPU1: Initial APIC ID: 1
Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
Total of 2 processors activated (9587.41 BogoMIPS).
activating NMI Watchdog ... done.
testing NMI watchdog ... OK.
Using local APIC timer interrupts.
Detected 16.638 MHz APIC timer.
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
time.c: Using PIT/TSC based timekeeping.
checking if image is initramfs... it is
NET: Registered protocol family 16
PCI: Using configuration type 1
PCI: Using MMCONFIG at e0000000
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 *9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 14 15) *0, disabled.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 169
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 177
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 185
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
GSI 20 sharing vector 0xC9 and IRQ 20
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 201
GSI 21 sharing vector 0xD1 and IRQ 21
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:03:06.0[A] -> GSI 21 (level, low) -> IRQ 177
PCI-DMA: Disabling IOMMU.
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1159892507.324:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 40E182233A4BCA05
- User ID: CentOS (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
ACPI: Thermal Zone [THRM] (45 C)
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Unknown: IDE controller at PCI slot 0000:00:1f.2
ACPI: PCI interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 209
Unknown: chipset revision 2
Unknown: 100% native mode on irq 209
ide0: BM-DMA at 0xf600-0xf607, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf608-0xf60f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: WDC WD2500JS-00NCB1, ATA DISK drive
Using cfq io scheduler
ide1 at 0xf800-0xf807,0xf702 on irq 209
Unknown: IDE controller at PCI slot 0000:00:1f.5
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 209
Unknown: chipset revision 2
Unknown: 100% native mode on irq 209
ide2: BM-DMA at 0xef00-0xef07, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xef08-0xef0f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
hde: WDC WD2500JS-00NCB1, ATA DISK drive
APIC error on CPU0: 00(60)
ide2 at 0xf300-0xf307,0xf202 on irq 209
Probing IDE interface ide3...
Unknown: IDE controller at PCI slot 0000:02:00.0
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169
Unknown: chipset revision 2
Unknown: 100% native mode on irq 169
ide4: BM-DMA at 0xbb00-0xbb07, BIOS settings: hdi:pio, hdj:pio
ide5: BM-DMA at 0xbb08-0xbb0f, BIOS settings: hdk:pio, hdl:pio
Probing IDE interface ide4...
Probing IDE interface ide5...
hdk: PIONEER DVD-RW DVR-111, ATAPI CD/DVD-ROM drive
ide5 at 0xbd00-0xbd07,0xbc02 on irq 169
Probing IDE interface ide0...
Probing IDE interface ide3...
Probing IDE interface ide4...
hdc: max request size: 1024KiB
hdc: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63
APIC error on CPU0: 60(60)
hdc: cache flushes supported
hdc:<7>APIC error on CPU0: 60(60)
hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 >
hde: max request size: 1024KiB
APIC error on CPU0: 60(60)
hde: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63
APIC error on CPU0: 60(60)
hde: cache flushes supported
hde:<7>APIC error on CPU0: 60(60)
hde1 hde2 hde3 hde4 <<7>APIC error on CPU0: 60(60)
hde5<7>APIC error on CPU0: 60(60)
hde6 >
APIC error on CPU0: 60(60)
APIC error on CPU0: 60(60)
hdk: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 131072 (order: 9, 2097152 bytes)
TCP: Hash tables configured (established 131072 bind 131072)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
cpufreq: CPU0 - ACPI performance management activated.
cpufreq: *P0: 2400 MHz, 88000 mW, 160 uS
cpufreq: P1: 1600 MHz, 56000 mW, 160 uS
cpufreq: CPU1 - ACPI performance management activated.
cpufreq: *P0: 2400 MHz, 88000 mW, 160 uS
cpufreq: P1: 1600 MHz, 56000 mW, 160 uS
ACPI: (supports S0 S1 S4 S5)
ACPI wakeup devices:
PCI0 PEX0 PEX1 PEX2 PEX3 PEX4 PEX5 HUB0 UAR1 UAR2 IGBE USB0 USB1 USB2 USB3 USB4 USB6 USB7 AZAL
Freeing unused kernel memory: 196k freed
SCSI subsystem initialized
libata version 1.20 loaded.
md: raid1 personality registered as nr 3
md: Autodetecting RAID arrays.
APIC error on CPU0: 60(60)
md: autorun ...
md: considering hde2 ...
md: adding hde2 ...
md: adding hdc3 ...
md: created md0
md: bind<hdc3>
md: bind<hde2>
md: running: <hde2><hdc3>
md: md0: raid array is not clean -- starting background reconstruction
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
md: syncing RAID array md0
md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc.
md: using maximum available idle IO bandwith (but not more than 200000 KB/sec) for reconstruction.
md: using 128k window, over a total of 221576448 blocks.
md: resuming recovery of md0 from checkpoint.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
security: 3 users, 4 roles, 355 types, 26 bools
security: 55 classes, 22582 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev hdc5, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), not configured for labeling
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
inserting floppy driver for 2.6.9-42.ELsmp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
hw_random hardware driver 1.0.0 loaded
ACPI: PCI interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 185
ehci_hcd 0000:00:1a.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: irq 185, pci mem ffffff0000068000
SELinux: initialized (dev usbdevfs, type usbdevfs), uses genfs_contexts
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 201
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 201, pci mem ffffff000006a000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 169
uhci_hcd 0000:00:1a.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: irq 169, io base 000000000000ff00
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 177
uhci_hcd 0000:00:1a.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: irq 177, io base 000000000000fe00
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 201
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 201, io base 000000000000fd00
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 209
uhci_hcd 0000:00:1d.1: UHCI Host Controller
usb 1-2: new high speed USB device using address 2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 209, io base 000000000000fc00
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 185, io base 000000000000fb00
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Generic Model: STORAGE DEVICE Rev: 9317
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
USB Mass Storage device found at 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb 7-1: new low speed USB device using address 2
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-1
ACPI: Power Button (FF) [PWRF]
EXT3 FS on hdc5, internal journal
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdc1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hdc1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev md0, type ext3), uses xattr
Adding 2048276k swap on /dev/hdc2. Priority:-1 extents:1
Adding 2048248k swap on /dev/hde1. Priority:-2 extents:1
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: No new microdata for cpu 1
microcode: No new microdata for cpu 0
IA-32 Microcode Update Driver v1.14 unregistered
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4091 buckets, 32728 max) - 456 bytes per conntrack
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
APIC error on CPU0: 60(60)
（数百行続く）
APIC error on CPU0: 60(60)
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80405540(lo)
APIC error on CPU1: 60(60)
APIC error on CPU1: 60(60)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
APIC error on CPU1: 60(60)
APIC error on CPU0: 60(60)
（数百行続く）
APIC error on CPU0: 60(60)